Frequently asked questions

• • What do I need to start using Reslin®?

  • What is the ratio of the components in Reslin®?

  • How should I heat Reslin®?

  • How strong will my Reslin® object be after hardening?

  • Can I add different additives to the Reslin® mixture?

  • How can I prevent air bubbles?

  • What can I do to ensure that my object hardens quickly?

  • What substances can I mix with Reslin®?

  • Is Reslin® food safe?

  • Can I use Reslin® for hot drinks or candles?

  • What is the ideal thickness for my Reslin® object?

  • Why do I have sticky spots on my object?

  • Should I use an oven to heat Reslin®?

  • Is Reslin® as dangerous as epoxy resin?

  • Can all silicone moulds be used for Reslin®?

What do I need to get started with Reslin®?

Reslin® activator and oil. A silicone mould. A convection oven. A bowl. A spatula or mixing rod. Any additives such as GlassRoxx, colour pigment, or other creative additives of your choice.

What is the ratio of Reslin® components?

Always use one part Reslin® activator for every two parts Reslin® oil. Therefore, the ratio is 1 to 2.

How should I heat Reslin®?

You should heat Reslin® by following these steps: Heat the Reslin® oil and Reslin® activator for 20 minutes at 60 °C (140 °F). Let the mixture stand for 20 minutes. Heat for 20 minutes at 90 °C (200 °F). Increase the temperature to 120 °C (250 °F) and reheat for 20 minutes. Important: Do not use a microwave to heat your Reslin®. For best results, use a convection oven.

How strong will my Reslin® object be after hardening?

The hardness of Reslin® depends on the additives you use and the thickness of the object. Without additives and with a thin layer (5 mm), the object may remain flexible. If you use an additive, such as GlassRoxx®, the object will harden. The finer the grain, the harder the object will be.

Can I add different additives to the Reslin® mixture?

Yes, you can add different materials to the Reslin® mixture, such as: powdered pigments, alcohol ink or natural mica for colour. GlassRoxx® for extra texture and colour (keep in mind the proportions of 2 to 3). Flakes of Jesmonite, coffee, herbs, dried flowers, spices and even Reslin® glass beads in 18 colours to achieve unique effects.

Note: Pay attention to the specific gravity of the materials. Materials with a lower specific gravity will float to the top of the mould. Dried berries, star anise, leaves, etc., are light and will float to the top of the mould during firing. So they will be at the bottom of the object. Substances with a high specific gravity sink in the mould! If you add a small amount of Reslin® or GlassRoxx® glass beads, everything will sink to the bottom and you will have a rim at the top of the object.

How can I prevent air bubbles?

If you place the mould filled with Reslin® on a vibrating plate, most of the air bubbles will disappear. Keep in mind that the added materials may sink when using a vibrating plate. Depending on the effect you want to achieve, you can choose whether or not to vibrate the mould.

What can I do to ensure that my object hardens quickly?

It is important to mix the Reslin® well and choose the right cooling method. The object can be removed from the oven immediately after heating and placed in cold water for faster cooling.

What substances can I mix with Reslin®?

Almost anything can be mixed with Reslin®, but avoid materials that contain water, such as fresh fruit. These can rot and biodegrade the mixture. Mix low-density substances with care, as they may float to the surface of the object.

Is Reslin® suitable for food use?

Yes, Reslin® is made from 100% natural and biodegradable components and is completely safe for contact with food.

Can I use Reslin® for hot drinks or candles?

Hot drinks: it is not recommended to pour hot drinks into a Reslin® object, as the heat may affect its structure. Candles: Reslin® is not suitable for candles, as the flame may burn the material.

What is the ideal thickness for my Reslin® object?

Ensure that your object is at least 5 mm thick, especially in the thinnest areas. Examine your mould carefully or use a Reslin® silicone mould tested by us for best results.

Why do I have sticky spots on my object?

Sticky spots can appear when Reslin® is not mixed properly. This can cause Reslin® activator residue to form strings and not activate completely.

Should I use an oven to heat Reslin®?

No, but we strongly recommend heating Reslin® in a conventional oven to ensure it is fully activated. If you are patient, you can also wait for the mixture to harden on its own (after 36 hours). This will slightly lighten the colour (if you are not using colour pigments).

Is Reslin® as dangerous as epoxy resin?

No, Reslin® is non-toxic and does not contain any harmful volatile substances, so there is no need to wear gloves or safety goggles. However, be careful with the activator, as it contains acids that can irritate the eyes.

Can all silicone moulds be used for Reslin®?

Yes, all silicone moulds can be used to work with Reslin®. But depending on the type of silicone mould you use, your object may have a satin or matte finish after demoulding.